connecting bolt
英 [kəˈnektɪŋ bəʊlt]
美 [kəˈnektɪŋ boʊlt]
网络 连接螺栓
双语例句
- The utility model is composed of a front shaft, a rear shaft, a shaft sleeve, a shoulder fitted with a bottom sleeve, a connecting bolt, a connecting nut, etc.
由前轴，后轴，轴套，与底套配合的台肩，连接螺栓，连接螺母等构成。 - Install connecting rod bolt protectors on rod bolts.
在连杆螺栓上安装连杆螺栓保护件。 - One-way fixing bolt and one-way connecting bolt
单向固定螺栓和单向连接螺栓 - This paper discusses the fatigue strength and the fatigue life of connecting rod bolt and analyses its fracture reason, based on the fatigue test of connecting rod bolt for16V280ZJ diesel engine.
对16V280ZJ型机车柴油机的连杆螺钉进行了疲劳试验，研究了连杆螺钉的疲劳强度和疲劳寿命，分析了其断裂失效原因。 - Analysis and Calculation of Connecting Bolt Fatigue Strength in Cross Shaft Universal Joint
十字轴万向联轴器联接螺栓疲劳强度分析与计算 - Improvement on Design Method for Connecting Rod Bolt
连杆螺栓设计方法的改进 - In this paper the causes of the connecting rod bolt failure in motor vehicle engines are discussed, and the improving measures are suggested as wall.
分析了发动机连杆螺栓损坏的原因，提出了改进措施。 - Failure Analysis for Down Rod Connecting Bolt of Pumping Uint
抽油机连杆下接头连接螺栓失效分析 - Stress Analysis and Fatigue Life Research for Connecting Rod Bolt
连杆螺栓的应力分析与疲劳寿命研究 - The quality guaranty at connections with high tension connecting bolt in Xupu Bridge
徐浦大桥高强螺栓连接质量保证 - Fatigue Life Analysis of the High Strength Connecting Rod Bolt
高强度连杆螺栓的疲劳寿命分析 - Some improving mesures for connecting rod bolt are proposed to improve its fatigue strength and fatigue life.
通过试验研究提出了对连杆螺钉的改进措施，以提高连杆螺钉的疲劳强度及疲劳寿命。 - This article deals with the test means of the anti-smooth coefficient of the component for high strength and big turret connecting bolt used in steel construction, and on the base of the large test datas, analyses and discusses its influence factors.
从介绍钢结构大六角头高强度螺栓连接构件抗滑移系数的测试方法着手，在总结大量实测数据的基础上，对影响抗滑移系数的相关因素进行了初步的探讨。 - Failure Analysis of Flange Connecting Bolt Rupture
法兰连接螺栓断裂失效的分析研究 - The connecting bolt of the main generator rotor spindle for the locomotive take place a continues break in operation.
机车用主发电机转子的连接螺栓在运行过程中发生连续断裂。 - Reliability Analysis of Connecting Bolt
螺栓联接的可靠性分析 - Fracture analysis of connecting bolt in a converter
转炉连接螺栓的断裂分析 - The reliability calculation of connecting bolt of hydraulic gate hoist cylinder cap
液压启闭机缸盖联接螺栓的可靠性计算 - Based on the analysis of uncertain factors affecting the connecting bolt reliability, internal model are used to describe the uncertain parameters such as load and stress. The non-probabilistic reliability design of the connecting bolt on static strength is proposed.
在分析影响螺栓联接可靠性不确定性因素的基础上，将不确定的载荷、应力等用凸模型中区间变量来描述，提出了螺栓联接静强度的非概率可靠性设计方法。 - Non-probabilistic Reliability Design Research on Connecting Bolt on Static Strength
螺栓联接静强度的非概率可靠性设计研究 - The existence of reticulation and mass shape ferrite, decarbonization at the screw thread surface layer which induced decline of fatigue strength of connecting bolt were also the important reasons of fracture.
此外，显微组织中网状、块状铁素体的存在以及螺纹表层脱碳使连接螺栓疲劳强度下降也是造成断裂的重要原因。 - In this paper analysis are made of the cause for scoring ocurrence on the connecting rod bolt bearing surface of Model 180 diesel engine and the effect of scoring on tightening force and improvement as well as tightening method appropriate to connecting rod bolts of 180 engines are presented.
本文分析了180柴油机连杆螺钉支承平面引起咬毛的原因及咬毛后对预紧力的影响，提出了改进措施和适合180柴油机连杆螺钉的拧紧方法。 - The Research on Connecting Rod Bolt Fracture of a Marine Diesel Engine
某船用柴油机连杆螺栓断裂研究 - Analysis of the breakage of the connecting bolt used in the coupling in 2 high mill
二辊轧机联轴器连接螺栓断裂事故分析 - Fracture Failure Analyses of Piston Connecting Bolt of Diesel Engine for Ship
船用柴油机活塞连接螺栓断裂失效分析 - Through the failure analysis of connecting bolt of down rod, it points out that it is not correct to put the thinner nut outer side if the double nut anti-loose method is adopted.
通过对游梁式抽油机对接式连杆下接头连接螺栓的失效分析，指出了采用双螺母防松时，将薄型螺母放置在外侧是不恰当的。 - Locking Types and Correct Assembly of Connecting Rod Bolt
连杆螺栓（钉）锁紧种类及正确装配 - Improving on Bit Connecting Bolt of LC-40
LC-40钻机钻头联接螺栓的改进设计 - This thesis introduces pretension element to simulate the pretension force of each connecting bolt and sets up a lot of contact elements in the match surface of parts, so obtains more reasonable results.
本文采用了预紧单元来模拟各连接螺栓的预紧力，同时在各零件间的配合表面设置大量接触单元，以获得更加合理的结果。 - And on the basis, the strength of the connecting bolt is checked.
并与有冷却时的温度、应力及变形进行比较，并在此基础上对活塞连接螺栓的强度进行了校核。